Customer Rating: - limited uses
this tool is almost too small. i have found very few uses where a simple cut-off wheel would not do just as well. the accessory does a fine job when you do find the right situation, however.
Customer Rating: - Yes, but...
I use my mini-rip saw all the time; it's absolutely essential to my art work. But I can't recommend it without a few comments.
First: that safety housing around it is so bulky that you cannot really see where the blade is going to go, exactly. This is fine if you're cutting something roughly, and you don't care within an 1/8 of an inch where the blade touches your work, but otherwise it's maddening. When I first bought it I tried it for a few cuts then put it aside to return. Instead what I did was attach it into one Dremel and use my other one, with a diamond cut-off wheel inserted, and lop the whole front of that silly cage off. If you do this, be mindful of where it is sealed to keep in the lubricating oil, and leave the back face of the safety on to help you keep the blade straight up and down. Once you do this little surgery, of course, you're out of warrantee, but then, WOW! this little guy is super handy! It's a detail saw with a dream-kerf of about a millimeter. Make SURE you wear goggles, now, dust and bits are going to fly.
Second: I don't know the solution to this second problem. I used my mini-saw so much, for so long, cutting through tempered hard-board that the blade got quite overheated and warped. When I finally realized I should have changed it a while ago, I found that the screw holding it in had fused to the blade and I couldn't get it off. The spindle-lock for the tool gave out before the screw moved, and I ended up bending the shaft of the saw trying. I would have returned it to Dremel, but since I had cut off the safety as I described, there was no chance. Ultimately I decided I had gotten far more than my money's worth out of the tool anyway, and bought a new one. I still use it every day. I guess I'm just going to have to be careful to change the blade sooner this time.
Customer Rating: - Nice except the shield can get in the way
The integral safety shield is a good idea but it gets in the way of seeing the path of the blade. It also means that whatever you are cutting must not have any protrusions that might obstruct the path of the saw/shield.
It did do a good job when we replaced our kitchen counter.. the old top was glued solid to the formica backsplash which we managed to save.
Customer Rating: - Works OK - barely...
I bought this to trim some 1/4" plywood from underneath a cabinet (couldn't get a chisel in there) and it worked just OK. To cut about a 1 foot section took about 10 minutes with a ton of burning and smoking of the blade and grinding to a halt (absolutely no torque) when met with a bit of resistance. It might work ok for balsa wood, but for anything else it is too weak a blade (carbide tipped would be better). Also, the blade guard is annoying because you can't get flush up to your edge (leaves about 1/8" or so of wood still along the joint). It's also annoying how you have to change out the head unit of your dremel, making it time consuming to switch back to normal collet and bits.
Sales of semiconductors in November indicate that consumer products such as LCD (liquid crystal display) TVs, digital music players, and other devices sold well during the holidays, the Semiconductor Industry Association (SIA) said Monday.
November chip sales rose 2.3 percent year-on-year to $23.1 billion, the SIA said.
Unit demand has far outpaced last year. But falling chip prices have hurt industry revenue, the chip association said. For example, DRAM (dynamic RAM) bit shipments grew 25 percent in the three months through mid-December, but average selling prices have declined 20 percent over the same period.
The association also noted that rising energy prices and concerns about the sub-prime lending issue in the U.S. do not appear to have had a significant impact on consumer spending for the holidays, the SIA said. The group reiterated its forecast that worldwide semiconductor sales will reach a new record in 2007. But it will take a stronger than expected December selling season to reach the 3.8 percent growth goal the group had forecast earlier this year, the SIA said.
Investment banking firm Credit Suisse was not as optimistic as the SIA.
The November data was below normal seasonal trends, noted analyst John Pitzer, in a report on Monday. Even if December reaches its normal seasonal growth, 2007 industry revenue will only reach $255.7 billion, up 3.2 percent over last year. The growth percentage would fall short of the SIA's 3.8 percent target.
The slow November prompted Credit Suisse to lower its 2008 chip industry revenue forecast to 9.4 percent year-on-year growth, down from a previous target of 13 percent.
Editor Annalee Newitz reveals the inspiration for the futurism-focused site's name, shares her obsession with the scientifically taboo and tells why sci-fi is going mainstream.